Page Comparison

...

After reviewing several concepts, we selected a four-bar mechanism as the simplest and most reliable method of producing a useful walking motion. Our mechanism design produced a semi-circle output, almost identical to the Chebyshev Lamda Mechanism, and our goal was to connect two of these mechanisms together to move a single leg and foot, with another two mechanisms moving a second leg offset by 180º from the first.

On top of Surmounting our walking mechanism we planned to build a moving counterweight that keeps the robot's center of mass above its shifting support polygon. We iterated through several different concepts of how to achieve this reliably.

We planned to produce as many parts as possible using 3D printing, as this would give us good strength and durability and oustanding outstanding manufacturing flexibility. Laser cut acrylic would be far too brittle for a mobile robot and delrin or aluminum would be too heavy for a small mobile robot and too slow and expensive to machine considering the multiple iterations we expected to produce. 3D printed PLA allowed us to rapidly manufacture and iteratively improve our many detailed parts at negligible cost.

...

Because our robot is mobile and must support and move its own weight, we needed to reduce mass wherever possible. We initially attempted to use a motor and gearbox available from a previous project. It was very small, very lightweight, and free. It used an inexpensive brushed DC motor powered by a AA-battery pack to drive a double-worm-gear reduction. Unfortunately we attached the drive system to our walking mechanism and found that it was not powerful enough to drive the legs, much less the counterweight, even at low speed. A much more powerful drive system was needed.

...

We were provided with a much larger and more powerful brushed DC motor, but had avoided using it up to this point due to its size and weight. In order to minimize both of these parameters, we removed the drive's encoder, associated electronics, and all-metal gearbox. We then printed a set of reduction gears using spur gears from our gear generator to decrease speed and increase torque at the gearbox output. After several quick iterations, we found that a reduction of 36.75:1 (8:24, 8:28, 8:28) produced approximately 15 RPM with more than adequate torque to drive our entire robot. 15 RPM results in one step every ~2 seconds, which is ideal for our robot with its sliding counterweight.

...

On the subject of timing belts, we initially attempted to transmit rotary power using round-belt pulleys and dacron string. However, we quickly found that the low-friction dacron string would not grip the smooth, printed PLA surface. Wrapping the string around the pulleys multiple times created more problems than it solved and tying the string into loops by hand did not allow us to adjust string tension easily, precisely, or repeatably. To correct these problems, we replaced our string and round-belt pulleys with timing belts and toothed pulleys. We then printed simple screw-driven tensioners and selected belt sizes by drawing their arrangement in Solidworks. Timing belts worked very well and produced no unexpected problems. One belt transmits power from motor/gearbox to walking mechanism crankshaft and two more transmit from crankshaft to counterweight.

...

Our first design was a four-bar mechanism intended to carry the motor's battery pack as weight. The problems with this concept were that the battery pack did not weigh enough to balance the robot and that traditional bar mechanisms are smooth and continuous, whereas our counterweight needed movement that was sharp and discontinuous. Ideally, our counterweight would sit motionless above the grounded foot, then move quickly to the other foot during the brief period of time when where both feet were in contact with the ground. We produced a four-bar mechanism that covered the desired range of motion but could not produce the desired time trajectory. Also it did not have the structural strength and stiffness required to hold a sufficiently sized counterweight mass.

...

Our second design replaced a continuous bar linkage with a discontinuous contact-driven mechanism. We created a see-saw that would rotate with the robot's legs and would collide with tabs placed on top of the body that would cause the see-saw to flip at desired times, shifting a sliding counterweight from one foot to the other along a slide bearing. Instead of using our battery pack as weight, we machined a cylindrical piece of carbon steel to fit over the slide bearing. The primary problem with this design was its complexity and its partially-constrained nature. In order to fully constrain the 3DOF counterweight and prevent it from moving in uncontrolled ways, we would have to construct very complex high-DOF joints to connect it to the legs. If we allowed it to move partially constrained, the robot would not be able to balance reliably.

...

Our third and final design combined the strengths and eliminated the problems of the first and second. We created a rotating cylinder with a sliding counterweight inside that combined the fully-constrained nature of the four-bar with the discontinuous nature of the see-saw. Our weight slides along an angled shaft that rotates synchronously with the walking mechanism's crankshaft, shifting the weight quickly from the lifting foot to the landing foot precisely during the short period of time while both feet are on the grounddouble support phase. Timing is also easily and precisely adjustable by simply loosening and moving the timing belt.

...

Next Section: Results